View MT8952_9560.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
ISO-CMOS ST-BUSTM FAMILY MT8952B HDLC Protocol Controller
Features
* * * * * * * * Formats data as per X.25 (CCITT) level-2 standards Go-Ahead sequence generation and detection Single byte address recognition Microprocessor port and directly accessible registers for flexible operation and control 19 byte FIFO in both send and receive paths Handshake signals for multiplexing data links High speed serially clocked output (2.5 Mbps) ST-BUS compatibility with programmable channel selection for data and separate timeslot for control information Independent watchdog timer Facility to disable protocol functions Low power ISO-CMOS technology Data link controllers and protocol generators Digital sets, PBXs and private packet networks D-channel controller for ISDN basic access C-channel controller to Digital Network Interface Circuits (typically MT8972) Interprocessor communication
ISSUE 5
May 1995
Ordering Information MT8952BC 28 Pin Ceramic DIP MT8952BE 28 Pin Plastic DIP MT8952BP 28 Pin PLCC MT8952BS 28 Pin SOIC -40C to 85C
Description
The MT8952B HDLC Protocol Controller frames and formats data packets according to X.25 (Level 2) Recommendations from the CCITT.
* * * * * * * *
Applications
TEOP C-Channel Interface Transmit FIFO Transmit Logic Zero Insertion Flag/Abort Generator CDSTo
D0-D7 Micro Processor R/W CS E IRQ WD Interface Control Address Decoder Interrupt Registers and Status Register Timing Logic F0i CKi RxCEN TxCEN
A0-A3
VDD VSS RST
Receive FIFO
Receive Logic
Address Detection
Zero Deletion
Flag/Abort/ Idle Detection
CDSTi
REOP
Figure 1 - Functional Block Diagram
3-61
MT8952B
ISO-CMOS
TxCEN RxCEN CDSTo CDSTi WD IRQ A0 A1 A2 A3 CS E R/W VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14
28 27 26 25 24 23 22 21 20 19 18 17 16 15
VDD RST F0i CKi TEOP REOP D7 D6 D5 D4 D3 D2 D1 D0
4 3 2 1 28 27 26
*
CDSTi CDSTo RxCEN TxCEN VDD RST F0i
28 PIN PDIP/CERDIP/SOIC
Figure 2 - Pin Connections
Pin Description
Pin No. 1 Name TxCEN Description Transmit Clock Enable - This active LOW input enables the transmit section in the External Timing Mode. When LOW, CDSTo is enabled and when HIGH, CDSTo is in high impedance state. If the Protocol Controller is in the Internal Timing Mode, this input is ignored. Receive Clock Enable - This active LOW input enables the receive section in the External Timing Mode. When LOW, CDSTi is enabled and when HIGH, the clock to the receive section is inhibited. If the Protocol Controller is in the Internal Timing Mode, this input is ignored. C and D channel Output in ST-BUS format - This is the serial formatted data output from the transmitter in NRZ form. It is in ST-BUS format if the Protocol Controller is in Internal Timing Mode with the data in selected timeslots (0,2,3 and 4) and the C-channel information in timeslot No. 1. If the Protocol Controller is in External Timing Mode, the formatted data is output on the rising edge of the clock (CKi) when TxCEN LOW. If TxCEN is HIGH, CDSTo is in high impedance state. C and D channel Input in ST-BUS format - This is the serial formatted data input to the receiver in NRZ form. It must be in ST-BUS format if the Protocol Controller is in Internal Timing Mode with the input data in selected timeslots (0,2,3 and 4) and the C-channel information in timeslot No.1. If the Controller is in External Timing Mode, the serial input data is sampled on the falling edge of the clock CKi when RxCEN is LOW. If RxCEN is HIGH, the clock to receive section is inhibited. Watch-Dog Timer output - Normally a HIGH level output, going LOW if the Watchdog timer times out or if the external reset (RST) is held LOW. The WD output remains LOW as long as RST is held LOW. Interrupt Request Output (Open Drain) - This active LOW output notifies the controlling microprocessor of an interrupt request. It goes LOW only when the bits in the Interrupt Enable Register are programmed to acknowledge the source of the interrupt as defined in the Interrupt Flag Register. Address Bus Inputs - These bits address the various registers in the Protocol Controller. They select the internal registers in conjunction with CS, R/W inputs and E Clock. (Refer to Table 1.)
2
RxCEN
3
CDSTo
4
CDSTi
5
WD
6
IRQ
7-10
A0-A3
3-62
E R/W VSS D0 D1 D2 D3
12 13 14 15 16 17 18
WD IRQ A0 A1 A2 A3 CS
5 6 7 8 9 10 11
25 24 23 22 21 20 19
CKi TEOP REOP D7 D6 D5 D4
28 PIN PLCC
ISO-CMOS
Pin Description (continued)
Pin No. 11 12 13 14 15-22 23 Name CS E R/W VSS D0-D7 REOP Description
MT8952B
Chip Select Input - This is an active LOW input enabling the Read or Write operation to various registers in the Protocol Controller. Enable Clock Input - This input activates the Address Bus and R/W input and enables data transfers on the Data Bus. Read/Write Control - This input controls the direction of data flow on the data bus. When HIGH, the I/O buffer acts as an output driver and as an input buffer when LOW. Ground (0 Volt). Bidirectional Data Bus - These Data Bus I/O ports allow the data transfer between the HDLC Protocol Controller and the microprocessor. Receive End Of Packet (Output) - This is a HIGH going pulse that occurs for one bit duration when a closing flag is detected on the incoming packets, or the incoming packet is aborted, or when an invalid packet of 24 or more bits is received. Transmit End Of Packet (Output) - This is a HIGH going pulse that occurs for one bit duration when a packet is transmitted correctly or aborted. Clock Input (Bit rate clock or 2 x bit rate clock in ST-BUS format while in the Internal Timing Mode and bit rate Clock in the External Timing Mode) - This is the clock input used for shifting in/out the formatted packets. It can be at bit rate (C2i) or twice the bit rate (C4i) in ST-BUS format while the Protocol Controller is in the Internal Timing Mode. Whether the clock should be C2i (typically 2.048 MHz) or C4i (typically 4.096 MHz) is decided by the BRCK bit in the Timing Control Register. If the Protocol Controller is in the External Timing Mode, it is at the bit rate. Frame Pulse Input - This is the frame pulse input in ST-BUS format to establish the beginning of the frame in the Internal Timing Mode. This is also the signal clocking the watchdog timer. RESET Input - This is an active LOW Schmitt Trigger input, resetting all the registers including the transmit and receive FIFOs and the watchdog timer. Supply (5 Volts).
24 25
TEOP CKi
26
F0i
27 28
RST VDD
Address Bits A3 0 0 0 0 0 0 0 0 1 1 A2 0 0 0 0 1 1 1 1 0 0 A1 0 0 1 1 0 0 1 1 0 0 A0 0 1 0 1 0 1 0 1 0 1 Read FIFO Status Receive Data Control Receive Address C-Channel Control (Transmit) Timing Control Interrupt Flag Interrupt Enable General Status
Registers Write Transmit Data Control Receive Address C-Channel Control (Transmit) Timing Control Watchdog Timer Interrupt Enable -
C-Channel Status (Receive) Table 1. Register Addresses
3-63
MT8952B
Introduction
ISO-CMOS
address detection can be limited only to the upper six bits by setting HIGH both RA6/7 and RxAD bits in the Control Register. Frame Check Sequence (FCS): The 16 bits following the data field are the frame check sequence bits. The generator polynomial is: G(x)=x16+x12+x5+1 The transmitter calculates the FCS on all bits of the data field and transmits after the data field and before the end flag. The receiver performs a similar computation on all bits of the received data and FCS fields and the result is compared with FOB8Hex. If it matches, the received data is assumed error free. The error status of the received packet is indicated by D7 and D6 bits in the FIFO Status Register. Zero Insertion and Deletion:
The MT8952B HDLC Protocol Controller handles bit oriented protocol structure and formats the data as per the packet switching protocol defined in the X.25 (Level 2) recommendations of the CCITT. It transmits and receives the packeted data (information or control) serially in a format shown in Figure 3 , while providing the data transparency by zero insertion and deletion. It generates and detects the flags, various link channel states and the abort sequence. Further, it provides a cyclic redundancy check on the data packets using the CCITT defined polynomial. In addition, it can generate and detect a Go Ahead sequence and recognize a single byte address in the received frame. There is also a provision to disable the protocol functions and provide transparent access to the serial bus through the parallel port.
Frame Format
All frames start with an opening flag and end with a closing flag as shown in Figure 3. Between these two flags, a frame contains the data and the frame check sequence (FCS). FLAG One Byte DATA FIELD FCS FLAG One Byte
n Bytes Two (n 2) Bytes Figure 3. Frame Format
The Protocol Controller, while sending either data from the FIFO or the 16 bits FCS, checks the transmission on a bit-by-bit basis and inserts a ZERO after every sequence of five contiguous ONEs (including the last five bits of FCS) to ensure that the flag sequence is not simulated. Similarly the receiver examines the incoming frame content and discards any ZERO directly following the five contiguous ONEs. Abort: The transmitter aborts a frame by sending eight consecutive ONEs. The FA bit in the Control Register along with a write operation to the Transmit Data Register enables the transmission of abort sequence instead of the byte written to the register. On the receive side, the ABRT bit in the General Status Register is set whenever an abort sequence (7 or more continuous 1's) is received. The abort sequence causes the receiver to abandon whatever it was doing and start searching for a start flag. The FA bit in the Interrupt Status Register is set when an abort sequence is received following a start flag and at least four data bytes (minimum for a valid frame).
Flag: The flag is a unique pattern of 8 bits (01111110) defining the frame boundary. The transmit section generates the flags and appends them automatically to the frame to be transmitted. The receive section searches the incoming packets for flags on a bit-bybit basis and establishes frame synchronization. The flags are used only to identify and synchronize the received frame and are not transferred to the FIFO. Data: The data field refers to the Address, Control and Information fields defined in the CCITT recommendations. A valid frame should have a data field of at least 16 bits. The first byte in the data field is the address of the frame. If RxAD bit in the Control Register is HIGH, the incoming packet is recognized only if the address byte matches the byte stored in the Receive Address Register or the address byte is the All-Call Address (all ONEs). The LSB of the Receive Address Register is set LOW permanently and the comparison is done only on upper seven bits of the received address byte. The
3-64
Interframe Time Fill and Link Channel States
When the HDLC Protocol Controller is not sending packets, the transmitter can be in any of three states mentioned below depending on the status of the IFTF0 and IFTF1 bits in the Control Register. These bits are also used to disable the protocol function to provide the transparent parallel access to the serial bus through the microprocessor port.
ISO-CMOS
Idle state: The Idle state is defined as 15 or more contiguous ONEs. When the HDLC Protocol Controller is observing this condition on the receiving channel, the Idle bit in the General Status Register is set HIGH. On the transmit side, the Protocol Controller ends the Idle state when data is loaded into the transmit FIFO. Interframe time fill state: The Protocol Controller transmits continuous flags (7EHex) in Interframe time fill state and ends this state when data is loaded into the transmit FIFO. Go Ahead state: Go Ahead is defined by the 9 bit sequence 011111110 (7FHex followed by a ZERO), and hence contiguous 7F's appear as Go Aheads. Once the transmitter is in `Go Ahead' state, it will continue to remain so even after the data is loaded into the FIFO. This state can only be changed by setting the IFTF bits in the Control Register to something other than `GO Ahead'. The reception of this sequence is indicated by GA bit in the General Status Register and the Protocol Controller can generate an interrupt if enabled to do so by the GA bit in the Interrupt Enable Register. Transparent Data Transfer State: The Protocol Controller, in this state, disables the protocol functions defined earlier and provides bidirectional access to the serial bit streams through the parallel port. Like other states, the transparent data transfer can be selected in both timing modes.
MT8952B
The serial port can be configured to operate in two modes depending on the IC bit in the Timing Control Register. It can transmit/receive the packets on selected timeslots in ST- BUS format or it can, using the enable signals (TxCEN and RxCEN), transmit/receive the packets at a bit rate equal to CKi clock input. The microprocessor port allows parallel data transfers between the Protocol Controller and a 6800/6809 system bus. This interface consists of Data Bus (D0-D7), Address Bus (A0-A3), E Clock, Chip Select (CS) and R/W control. The microprocessor can read and write to the various registers in the Protocol Controller. The addresses of these registers are given in Table 2. The IRQ is an open drain, active LOW output indicating an interrupt request to CPU. Control and monitoring of many different interrupts that may originate from the protocol controller is implemented by the Interrupt Flag Register (IFR) and the Interrupt Enable Register (IER). Specific events have been described that set a bit HIGH in the Interrupt Flag Register. Such an event does not necessarily interrupt the CPU. To assert an interrupt (pull IRQ output LOW) the bit in IER that coincides with the Interrupt Flag Register must be set HIGH. The IRQ bit in the General Status Register is the complement of IRQ pin status. If an interrupt is asserted, this bit will be set HIGH otherwise it will be LOW. TEOP and REOP Outputs: The HDLC Protocol Controller provides two separate signals TEOP & REOP indicating the end of packet transmitted and received respectively. TEOP is a HIGH going pulse for one bit duration asserted during the last bit of the closing flag or Abort sequence of the transmit packet. REOP is also a HIGH going pulse occurring for one bit period when a closing flag is received or an incoming packet is aborted or an invalid packet of 24 or more bits is detected. However, REOP is not generated for invalid packets of length less than 24 bits. These `end of packet' signals are useful in multiplexing several data links on to a single HDLC Protocol Controller.
Invalid Frames
Any frame shorter than 32 bits between the opening and closing flags (corresponding to 16 bits of data and 16 bits FCS) is considered invalid. The Protocol Controller ignores the frame only if the frame length is less than 24 bits between the flags. For frames of length 24 to 32 bits, it transfers the data field to FIFO and tags it as having bad FCS in the FIFO Status Register.
Timing Modes
There are two timing modes the Protocol Controller can be run in. These timing modes refer only to the configuration of the serial port and are not related to the microprocessor port. Internal Timing Mode The Internal Timing Mode is intended for an easy interface to various products using ST-BUS
3-65
Functional Description
The functional block diagram of the HDLC Protocol Controller is shown in Figure 1. It has two ports. The serial port transmits and receives formatted data packets and the parallel port provides a microprocessor interface for access to various registers in the Protocol Controller.
MT8952B
ISO-CMOS
and asynchronous and have effect only after the current bit in the packet is transmitted/received. Although the protocol controller provides the packetized data on a limited number of channels on the ST-BUS while operating in the Internal Timing Mode, it can packetize the data on any or all the channels of the ST-BUS if it is operated in the External Timing Mode with appropriate enable signals on TxCEN and RxCEN.
architecture, particularly MITEL's Digital Network Interface Circuit (DNIC - MT8972). The data/packets are shifted in/out serially in ST-BUS format using the timing signals F0i and C2i/C4i. In addition to framing the data, the Protocol Controller reserves one channel (channel-1) on the ST-BUS for carrying control information (C-channel) and this timeslot can not be used for the packetized data. While the Protocol Controller is in the Internal Timing Mode, the clock input CKi can be either at the bit rate or at 2bit rate depending on the BRCK bit in the Timing Control Register as shown in Table 2. Output Data Rate 2.048 Mbps 2.048 Mbps
Transparent Data Transfer
By setting the IFTF bits in the Control Register appropriately, the protocol functions can be disabled. This provides a bidirectional access to the serial port through the microprocessor interface, with 19 byte deep FIFO in each direction. The transparent data transfer facility functions in bytewide format and is available in both timing modes except when the timing control bits are set for one bit/frame during the Internal Timing Mode. The transmit data is shifted out serially on CDSTo and the operation being bytewide, only the least significant bits of each byte loaded are transmitted, if the timing control bits are set to select 2, 6 or 7 bits/ frame. When the transmit FIFO is empty, the last byte or the portion the last byte, written to the FIFO is transmitted repeatedly. Similarly the serial data on CDSTi is shifted in and converted to bytewide format. In case the timeslot selected is 2, 6 or 7 bits/ frame, the reception involves only the most significant bits of each byte. It should be noted that none of the protocol related status or interrupt bits are applicable in transparent data transfer state. However, the FIFO related status and interrupt bits are pertinent and carry the same meaning as they do while performing the protocol functions.
BRCK Bit 0 1
CKi Input 4.096 MHz/C4i 2.048 MHz/C2i
Table 2. Output Bit Rate In Internal Timing Mode The Protocol Controller uses the ST-BUS timing signals F0i and C2i/C4i, and enables the transmitter and receiver sections in the appropriate timeslots as determined by TC0-TC3 bits in the Timing Control Register. The TxCEN and RxCEN inputs are ignored in this mode. C-Channel Interface This is a separate control channel (C-channel) interface relevant only in the Internal Timing Mode. The data stored in the C-Channel Control Register is shifted out during the channel-1 timeslot of the outgoing ST-BUS (CDSTo) and the C1EN bit in the Timing Control Register enables the transmission. The transmission of C-Channel is independent of packet/data transmission. The data received on channel-1 of the incoming ST-BUS (CDSTi) is shifted into the C-Channel Status Register independently and it is updated continuously. Both the C-channel registers are accessible by the accompanying CPU through the parallel port. External Timing Mode In the External Timing Mode, the transmit and receive sections are enabled independently by TxCEN and RxCEN control inputs and the formatted data packets are shifted in/out serially at a rate equal to the clock frequency on CKi. The output is transmitted on the rising edge and the receiver samples the input on the falling edge of the clock. The TxCEN and RxCEN controls are independent
Watchdog Timer
This is a fixed eleven stage binary counter with F0i as the input and WD as the output from the last stage. This counter can be reset either by the external input (RST) or by writing XXX0 1010 to the Watchdog Timer Register. The WD output is normally HIGH and if the Watchdog Timer Register is not written within 210 cycles of F0i input after it is reset, the WD output will go LOW for a period of 210 cycles of F0i. Even though the F0i input is not required for formatting data in the External Timing Mode, it is necessary for the operation of the watchdog timer.
3-66
ISO-CMOS
Order of Bit Transmission/Reception
The Least Significant Bit (LSB) corresponding to D0 on the data bus is transmitted first on the serial output (CDSTo). On the receiving side, the first bit received on the serial input (CDSTi) is considered as the LSB and placed on D0 of the data bus. Rx FIFO Status Bits D5 0 0 1 1 D4 0 1 0 1 Rx FIFO Empty
MT8952B
Status
Less than or equal to 14 bytes Rx FIFO Full Greater than or equal to 15 bytes Table 4. Receive FIFO Status
Registers
There are several registers in the HDLC Protocol Controller accessible to the associated microprocessor via the data bus. The addresses of these registers are given in Table 1 and their functional details are given below. FIFO Status Register (Read): This register (Figure 4) indicates the status of transmit and receive FIFOs and the received byte as described below. D7 D6 D5 D4 D3 D2 D1 D0
LOW
updated. When in internal 4.096 MHz timing mode, the MT8952B must receive four falling edges of the C4i clock before the Rx FIFO status bit will be updated (see the section on Receive Operation Normal Packets). Tx FIFO Status: These two bits (D3 and D2) indicate the status of transmit FIFO as shown in Table 5. Tx FIFO Status Bits D3 0 0 1 1 D2 0 1 0 Tx FIFO Full Greater than or equal to 5 bytes Tx FIFO Empty
Status
Rx Byte Status
Rx FIFO Tx FIFO LOW Status Status Figure 4 - FIFO Status Register
Rx Byte Status: These two bits (D7 and D6) indicate the status of the received byte ready to be read from the receive FIFO. The status is encoded as shown in Table 3. Rx Byte Status Bits D7 0 0 1 1 D6 0 1 0 Packet Byte First Byte Last Byte (Good FCS)
1 Less than or equal to 4 bytes Table 5. Transmit FIFO Status
Status
The Tx FIFO status bits are updated in the same manner as the Rx FIFO bits, except that in external timing mode, and in internal 2.048 Mbps timing mode, the Tx FIFO status bits are updated after two falling edges of the CKi or the C2i signal (see the section on Transmit Operation - Normal Packets). Receive Data Register (Read): Reading the Receive Data Register (Figure 5) puts the first byte from the receive FIFO on the data bus. The first bit of the data received on the serial input (CDSTi) is considered to be the LSB and is available on D0 of the data bus. D7
RD7
1 Last Byte (Bad FCS) Table 3. Received Byte Status
Rx FIFO Status: These bits (D5 and D4) indicate the status of receive FIFO as given by Table 4. The Rx FIFO status bits are not updated immediately after an access of the Rx FIFO (a read from the microprocessor port, or a write from the serial port), to avoid the existence of unrecoverable error conditions. When in external timing mode, the MT8952B must receive two falling edges of the clock signal at the CKi input before the Rx FIFO status bits will be updated. When in internal 2.048 MHz timing mode, the MT8952B must receive two falling edges of the C2i clock before the Rx FIFO status bits will be
D6
RD6
D5
RD5
D4
RD4
D3
RD3
D2
RD2
D1
RD1
D0
RD0
Figure 5 - Receive Data Register Transmit Data Register (Write): Writing to Transmit Data Register (Figure 6) puts the data present on the data bus into the transmit FIFO. The LSB (D0) is transmitted first.
3-67
MT8952B
D7
TD7
ISO-CMOS
D4
TD4
D6
TD6
D5
TD5
D3
TD3
D2
TD2
D1
TD1
D0
TD0
Figure 6 - Transmit Data Register Control Register (Read/Write): The Control Register (Figure 7) is used for general purpose control of the HDLC Protocol Controller. The bits contained in this register and their functions are described below. D7 D6 D5 D4 D3 D2 D1
FA
RA6/7 - Receive Address Six/Seven bits: This bit, when set HIGH, limits the address detection only to the upper six bits of the received address byte (last 6 bits of received address field) and when LOW, allows the address comparison on seven bits. An "all call", in this case is defined as all ONEs in the upper six bits only. RA6/7 is ignored if the address detection is disabled (RxAD=0). IFTF0 and IFTF1 - Interframe Time Fill: Setting these bits according to the table below (Table 6) causes the transmitter to be in one of the active or idle states or allows the Protocol Controller to be in the transparent data transfer state. IFTF Bits
IFTF1 IFTF0
D0
EOP
TxEN RxEN RxAD RA6/7 IFTF1 IFTF0
Figure 7 - Control Register TxEN -Transmit Enable: When set HIGH, this bit enables the transmitter and when LOW, disables it setting the serial output (CDSTo) to high impedance state. If the transmitter is disabled during the transmission of a packet using this bit, the Protocol Controller will wait until the completion of the packet and closing flag is transmitted or the packet is aborted before setting the output (CDSTo) to high impedance state. Thus TxEN bit controls the transmission packet by packet unlike TxCEN input (pin 1) which controls it bit-by-bit. However, if the Protocol Controller is in transparent data transfer state, the transmission will be stopped within two bit periods (maximum) and set the output to high impedance state. RxEN - Receive Enable: This bit enables the receiver when set HIGH and disables it when LOW. If this bit goes LOW during the reception of the packet, the receiver can only be disabled after the current packet and its closing flag are received or an abort is detected. Thus RxEN bit controls the receiver section packet by packet unlike RxCEN input (pin 2) which controls it bit-by-bit. However, if the Protocol Controller is in transparent data transfer state, the receiver will be disabled immediately. RxAD - Receive Address Detect: This bit when set HIGH, enables the address detection for the received packets. This causes the receiver to recognize only those packets having a unique address as programmed in the Receive Address Register or if the address byte is the All-Call address (all ONEs). The address comparison is done only on seven bits (compatible to the first byte of the address field defined in LAPD-CCITT) and an All-Call is defined as all ONEs in upper seven bits of the received address field. If RxAD is LOW, the address detection is disabled and every valid packet is recognized.
Result Idle State (All ONEs) Interframe Time Fill state (Continuous Flags) Transparent Data Transfer
0 0 1 1
0 1 0 1
Go Ahead state (Continuous 7FHEX) Table 6. Interframe Time Fill Bits
FA - Frame Abort: When set HIGH, this bit'tags' the next byte written to the transmit FIFO and causes an abort sequence (eight ONEs) to be transmitted when it reaches the bottom of the FIFO. The abort sequence will be transmitted instead of the byte that was tagged. The FA bit is cleared to ZERO upon writing the data to the transmit FIFO. As a result, a `read' of this register bit will not reflect the last data written to it. EOP - End Of Packet: Writing a ONE to this bit `tags' the next byte written to the transmit FIFO to indicate that it is the last data byte of the packet. This bit is cleared to ZERO upon writing the data to the transmit FIFO. As a result, a read of this register bit will not indicate the last data written to it. Receive Address Register (Read/Write): D7
RA7
D6
RA6
D5
RA5
D4
RA4
D3
RA3
D2
RA2
D1
RA1
D0
RA0
Figure 8 - Receive Address Register The data in this register (Figure 8) defines the unique address for the HDLC Protocol Controller. If address recognition is enabled using the RxAD and RA6/7 bits in the Control Register, an incoming packet is recognized only if its address byte (seven or six most significant bits) matches the corresponding bits in this register or if the address is
3-68
ISO-CMOS
an "all-call". The LSB of the Receiver Address Register is set LOW permanently and the address comparison is done only on remaining bits of the register. C-Channel Control Register (Read/Write): D7
CT7
MT8952B
state during that period. However, the C-channel information is received independently and the Cchannel Status Register is updated continuously. Note that C1EN has relevance only during the Internal Timing Mode. BRCK- Bit Rate Clock: This bit is used during the Internal Timing Mode to select the clock rate and ignored if the Protocol Controller is in the External Timing Mode. It should be set HIGH if the input clock (CKi) is at the bit rate (C2i) and should be LOW for the clock input at 2 x bit rate (C4i). In both cases, the clock should be properly phase related to F0i as shown in Figure 25. TC0-TC3 - Timing Control Bits: In the Internal Timing Mode the transmitter and the receiver sections are enabled during the times defined by the Timing Control Bits TC0-TC3 (Table 7). This applies only to the ST-BUS channels 0, 2, 3 and 4 carrying the packets or transparent data (channel-1 pertains to C-channel information). The output CDSTo is put during the remaining time intervals not enabled by these bits. ST-BUS Bits Channel /Frame TC3 TC2 TC1 TC0 Number X 0 0 0 0 1 X 0 0 1 0 2 0 0 1 0 0 6 1 0 1 0 0 7 X 0 1 1 2 8 X 1 0 0 3 8 X 1 0 1 4 8 X 1 1 0 2 and 3 16 X 1 1 1 2, 3 and 4 24 X : Don't Care Table 7. Timing Control Bits Interrupt Flag Register (Read): Reading the Interrupt Flag Register puts the interrupt status bits on the data bus. This register is reset when it is read and a particular bit will not be set until its particular condition occurs again. The functional details of each bit are provided in Figure 11. D7
GA
D6
CT6
D5
CT5
D4
CT4
D3
CT3
D2
CT2
D1
CT1
D0
CT0
Figure 9 - C-Channel Control Register The data written to this register (Figure 9) is transmitted on channel-1 slot of the outgoing STBUS (CDSTo), when enabled by C1EN bit in the Timing Control Register. This feature can only be used when the HDLC Protocol Controller is in the Internal Timing Mode. Timing Control Register (Read/Write): The Timing Control Register (Figure 10) controls the timing mode and other related operations and provides a software reset to the Protocol Controller. The various bits in this register are described below: D7
RST
D6
IC
D5
D4
D3
TC3
D2
TC2
D1
TC1
D0
TC0
Timing Control Bits
C1EN BRCK
Figure 10. Timing Control Register RST - Reset: When this bit is set HIGH, all the registers in the HDLC Protocol Controller are reset and the data in the FIFOs is lost. This is equivalent to the external reset with the exception that the RST bit does not affect itself or the Watchdog Timer Register and WD output. The RST bit must be "cleared" (written as a logic "0") twice before the MT8952B will be removed from its reset state (see section on RESET operation). IC - Internal Control: When this bit is cleared to ZERO, the Protocol Controller is in the External Timing Mode. The transmit and receive sections are enabled by the inputs TxCEN and RxCEN respectively, and F0i is used only for the watchdog timer operation. When this bit is a ONE, the Protocol Controller is in the Internal Timing Mode. The transmit and receive sections are enabled by the internally generated timings derived from the inputs CKi and F0i. The F0i input defines the beginning of a frame (Figure 24) and the transmitter and receiver sections are enabled in the timeslots as determined by the bits TCO-TC3. The inputs TxCEN and RxCEN are ignored in this mode. C1EN - Channel-1 Enable: When HIGH, it enables the transmission of C-channel information on channel-1 time-slot of the outgoing ST-BUS (CDSTo) and when LOW, puts CDSTo into high impedance
D6
EOPD
D5
Tx DONE
D4
FA
D3
D2
D1
Rx 15/19 FULL
D0
Rx OFLW
Tx Tx 4/19 URUN FULL
Figure 11. Interrupt Flag Register GA - Go Ahead: This bit when set HIGH, indicates the detection of `go ahead' sequence on the incoming data stream (CDSTi).
3-69
MT8952B
ISO-CMOS
enables the associated interrupt source. However, the masked bits in the IFR are still valid but they do not cause the IRQ output to go LOW. The description of the bits enabling the various interrupts is identical to those of the Interrupt Flag Register. General Status Register (Read): This register (Figure 12) contains the general status information on the Protocol Controller. D7 D6 D5
GA
EOPD - End of Packet Detect: A HIGH on this bit confirms the reception of an `end of packet' flag, an abort sequence or an invalid packet of 24 or more bits on the incoming data stream (CDSTi). Tx DONE - Transmitter Done: This bit, when HIGH, indicates that the packet transmission is complete and the Transmit FIFO is empty. The falling edge of TEOP output causes this interrupt status bit to be set HIGH if the FIFO is empty. FA - Frame Abort: This bit is set HIGH to indicate that a frame abort has been detected on the incoming data stream. Tx 4/19 FULL - Transmit FIFO 4/19 full: This bit if set HIGH, indicates that the transmit FIFO has only 4 bytes remaining in it and another 15 bytes could be loaded. This bit has significance only when the transmit FIFO is being depleted and not when it is getting loaded. Tx URUN - Transmit FIFO underrun: This bit when HIGH, identifies that the transmit FIFO is empty without the Protocol Controller being given the `end of packet' indication. This indicates that the transmit FIFO has underrun and the Protocol Controller will transmit an abort sequence automatically. Tx DONE will be set 8 bit times after Tx URUN is set. Rx15/19 FULL - Receive FIFO 15/19 full: This bit when HIGH, confirms that the receive FIFO has 15 bytes in it and it can receive four more bytes. Rx OFLW - Receive FIFO overflow: This bit when set HIGH, indicates that the receive FIFO is full and a `write' occurred indicating an overflow. The byte causing this and all the subsequent bytes written while the FIFO is in this state are lost. The receiver begins to search for a new start flag. Watchdog Timer Register (Write): The Watchdog Timer Register operates in conjunction with the Watchdog Timer and the WD output. Writing the code of XXX0 1010 in the register resets the WD timer. If the register is not re-written within 210 cycles of F0i after resetting the timer, the WD output goes LOW. This register serves the sole purpose of resetting the timer and hence relevant only if it is written with the above data. Interrupt Enable Register (Read/Write): This register enables/disables the interrupts as specified in the Interrupt Flag Register (IFR). Setting HIGH the appropriate bits in this register (IER)
3-70
D4
ABRT
D3
IRQ
D2
IDLE
D1
LOW
D0
HIGH
Rx Tx OFLW URUN
Figure 12 - General Status Register Rx OFLW - Receive FIFO overflow: This bit, if set HIGH, indicates that the receive FIFO has overflowed. The byte causing this and all the subsequent bytes written while the FIFO is in this state are lost. Note that this bit is the same as the Rx OFLW bit in Interrupt Flag Register (IFR) and can only be cleared by reading the IFR. Tx URUN - Transmit FIFO Underrun: When HIGH, this bit indicates that the transmit FIFO has underrun. Under this condition the packet being transmitted is aborted. This bit is the same as the Tx URUN bit in the Interrupt Flag Register (IFR) and can only be cleared when the IFR is read. GA - Go Ahead: This bit is set HIGH if a `go ahead' is received on the incoming data stream and is cleared when the Interrupt Flag Register is read. This bit is the same as the GA bit in the IFR. ABRT - Abort: The reception of contiguous seven ONEs on incoming data, sets this bit HIGH and reading the General Status Register, clears it. IRQ - Interrupt Request: This bit refers to the status of the interrupt request output from the Protocol Controller. If HIGH, it indicates that the IRQ (pin 6) output is LOW and vice versa. IDLE - Idle Channel: This bit, if set HIGH, identifies that the receiver is detecting an idle channel at its input (minimum 15 ONEs). C-Channel Status Register (Read): D7
CR7
D6
CR6
D5
CR5
D4
CR4
D3
CR3
D2
CR2
D1
CR1
D0
CR0
Figure 13. C-Channel Status Register The C-Channel Register (Figure 13) continuously stores the data received during the channel-1
ISO-CMOS
timeslot of the incoming ST-BUS (CDSTi) during the Internal Timing Mode of the Protocol Controller.
MT8952B
When the data is detected in the transmit FIFO, the protocol controller will proceed in one of the following ways: If the transmitter is in idle state, the present byte of eight ONEs being transmitted is completed and then followed by a start flag and subsequently the data in the transmit FIFO is transmitted. If the transmitter is in the interframe time fill state, the flag presently being transmitted is finished and then another start flag is transmitted before transmitting the data from the transmit FIFO. If the transmitter is in go ahead state, it continues to be in that state even after the data is loaded into the FIFO. Only when the IFTF bits are set to choose something other than go ahead will the data be transmitted. If the transmitter is in transparent data transfer state, the protocol functions are disabled and the data in the transmit FIFO is transmitted on CDSTo. To indicate that the particular byte is the last byte of the packet, the EOP bit in the Control Register must be set before the last byte is written into the transmit FIFO. The EOP bit is cleared automatically when the data byte is written to the FIFO. After the transmission of the last byte in the packet, the frame check sequence (16 bits) is sent followed by a closing flag. If there is any more data in the transmit FIFO, another flag is transmitted followed by the new data. In case of no data in the FIFO, the transmitter assumes the selected link channel state. During the transmission of either the data or the frame check sequence, the Protocol Controller checks the transmitted information on a bit by bit basis and inserts a ZERO after every sequence of five consecutive ONEs. Transmit FIFO Full: When the Transmit FIFO is full, this state is indicated by the Transmit FIFO status bits in the FIFO Status Register. These bits do not change state for two bit periods after an access of the FIFO from either the serial port or the microprocessor port. The bit period is determined by the CKi signal frequency. If the bus cycle of the controlling microprocessor is much shorter than the bit period, the Transmit FIFO status bits may not be updated in time for the next microprocessor read of the FIFO Status Register. To make sure that the microprocessor does not overwrite the Tx FIFO, if over four bytes of information have been written to the Tx FIFO, the
3-71
RESET
When the MT8952B is reset by a low going pulse on the RST pin or by setting (logic high) the RST bit in the Timing Control Register, the device is put into the following state: a) All bits in the Timing Control Register are cleared (logic 0) by an external reset. An internal reset clears all bits except the RST bit. b) All bits in the Interrupt Enable Register are cleared (logic 0). c) All bits in the Control Register are cleared (logic 0). d) All bits in the Interrupt Register are cleared (logic 0). e) All bits in the General Status Register are cleared (logic 0) except for the two least significant bits. f) Receive and Transmit Registers are cleared and the FIFO Status Register reflects their state accordingly. g) The WD output is reset low by an external reset but is not affected by an internal reset. h) The Transmitter and the Receiver are disabled.
Transmit Operation
After a reset, which the external circuitry should provide upon power up, the transmit section is disabled. Before enabling this section, the timing should be set up. On reset, the serial port is set to External Timing Mode. In case this is not desired, the Timing Control Register should be written to with the appropriate data. Once in the correct timing mode, the Transmit Enable (TxEN) bit in the Control Register can be set. Now that the transmitter is enabled it will be in the Idle channel state. If any other channel state or the transparent data transfer facility is required, the IFTF bits in the Control Register should be set accordingly. Normal Packets: To start a packet, the data is written into the transmit FIFO starting with the address field. All the data must be written to the FIFO in a bytewide manner.
MT8952B
ISO-CMOS
Transparent Data Transfer: The IFTF bits in the Control Register can be set to provide transparent data transfer disabling the protocol functions. The transmitter no longer generates the Flag, GA, Abort and Idle sequences nor does it insert the zeros and calculate the FCS . It operates in both timing modes in bytewide manner and transmits data serially on CDSTo. If the Protocol Controller is in the Internal Timing Mode and the Timing Control bits are set to select 2, 6 or 7 bits/ frame, the corresponding least significant bits of every byte loaded into the transmit FIFO are only transmitted. The transparent data transfer facility is not available when the Timing Control bits are set for 1 bit/frame. In case the FIFO is empty, the last byte or the portion of the last byte, written to the FIFO is transmitted repeatedly. Note that the transparent data transfer can be disabled immediately in software (unlike during the transmission of packets) using TxEN bit in the Control Register. The operation of the transmitter is similar in the External Timing Mode.
microprocessor should wait for a 4/19 FULL interrupt before writing to the Tx FIFO again. When a 4/19 FULL interrupt has been received, a maximum of 15 bytes should be written to the Tx FIFO, then transfer of information to the Tx FIFO should stop and the 4/ 19 FULL interrupt should be waited for once more. The FIFO may be allowed to empty if no more information is to be sent at the moment. This procedure should keep software independent of the frequency of the CKi signal. Transmit Underrun: A transmit underrun occurs when the last byte loaded into the transmit FIFO was not `flagged' with the `end of packet' (EOP) bit and there are no more bytes in the FIFO. In such a situation, the Protocol Controller transmits the abort sequence (eight ONEs) and moves to the selected link channel state. Abort Transmission: If it is desired to abort the packet currently being loaded into the transmit FIFO, the next byte written to the FIFO should be `flagged' to cause this to happen. The FA bit of the Control Register must be set HIGH, before writing the next byte into the FIFO. This bit is cleared automatically once the byte is written to the FIFO. When the `flagged' byte reaches the bottom of the FIFO, a frame abort sequence is sent instead of the byte and the transmitter operation returns to normal. Go Ahead Transmission: By setting the IFTF bits in the Control Register appropriately the transmitter can be made to send the Go Ahead sequences when the Protocol Controller is not sending the packets. Since the go ahead is defined as 011111110, contiguous 7FHex' s appear as go aheads. As long as the IFTF bits are set to choose go aheads, the transmitter will send them even if data is subsequently loaded into the FIFO. Only when the IFTF bits are set to select something other than go aheads, will the data be transmitted. C-Channel Transmission: By setting the C1EN bit in the Timing Control Register HIGH, the information loaded in the CChannel Control Register can be transmitted over channel-1 timeslot of the outgoing ST-BUS (CDSTo). This is available only during the Internal Timing Mode of the Protocol Controller.
Receive Operation
After a reset on power up, the receive section is disabled. Timing set up considerations are similar to that of the transmit section. Address detection is also disabled when a reset occurs. If address detection is required, the Receiver Address Register is loaded with the desired address and the RxAD bit in the Control Register is set HIGH. The receive section can then be enabled by RxEN bit in the Control Register. Normal Packets: After initialization as explained above, the serial data starts to be clocked in and the receiver checks for the idle channel and flags. If an idle channel is detected, the `Idle' bit in the General Status Register is set HIGH. Once a flag is detected, the receiver synchronizes itself in a bytewide manner to the incoming data stream. The receiver keeps resynchronizing to the flags until an incoming packet appears. The incoming packet is examined on a bitby-bit basis, inserted zeros are deleted, the FCS is calculated and the data bytes are written into the receive FIFO. However, the FCS and other control characters like the flag, abort etc., never appear in the FIFO. If the address detection is enabled, the first byte following the flag is compared to the byte in the Receive Address Register and to All-Call address. If a match is not found, the entire packet is ignored and nothing is written to the FIFO. If the incoming address byte is valid, the packet is received in normal fashion. All the bytes written to the receive
3-72
ISO-CMOS
FIFO are flagged with two status bits. The status bits are found in the FIFO status register and indicate whether the byte to be read from the FIFO is the first byte of the packet, the middle of the packet, the last byte of the packet with good FCS or the last byte of the packet with bad FCS. This status indication is valid for the byte to be read from the receive FIFO. The incoming data is always written to the FIFO in a bytewide manner. However, in the event of data sent not being a multiple of eight bits, the software associated with the receiver should be able to pick the data bits from the MSB positions of the last byte in the received data written to the FIFO. The Protocol Controller does not provide any indication as to how many bits this might be. Receive FIFO Empty: When the Receive FIFO is empty, this state is indicated by the Receive FIFO status bits in the FIFO Status Register. As with the Tx FIFO status bits (see Transmit FIFO Full Section), these bits are not updated for two bit periods after any access of the Receive FIFO. If the controlling microprocessor's bus cycle is much shorter than a bit period on the serial port, then the status bits may not be updated to indicate there is no information left in the Rx FIFO before the microprocessor has returned to read the Rx FIFO again. The result is an underflow condition that is only evident by redundant bytes in the received message. To avoid a Rx FIFO underflow, reading information from the Rx FIFO should be approached in two ways. The first approach is to be used when the MT8952B indicates (via interrupt) that the Rx FIFO is 15/19 FULL. The controlling microprocessor should then immediately read 14 bytes from the Rx FIFO. This will avoid emptying the FIFO. The second approach is to be used when an End of Packet interrupt is signalled by the MT8952B. The controlling microprocessor should then empty the Rx FIFO until the Rx Byte Status bits in the FIFO Status Register indicate that the byte about to be read is the last byte. These bits are "tag" bits whose state was determined before the End of Packet condition was indicated, therefore their state is valid. Invalid Packets: If there are less than 24 data bits between the opening and closing flags, the packet is considered invalid and the data never enters the receive FIFO. This is true even with data and the abort sequence, the total of which is less than 24 bits. The data packets that are at least 24 bits but less than 32 bits long are also invalid, but not ignored. They are
MT8952B
clocked into the receive FIFO and tagged as having bad FCS. Frame Abort: When a frame abort is received the appropriate bits in the Interrupt Flag and Status Registers are set. The last byte of the packet that was aborted is written to the FIFO with a status of `packet byte' tagged to it. The CPU determines which packet in the FIFO was aborted, if there is more than one packet in the FIFO, by the absence of `last byte' status on any of the bytes. Idle Channel: While receiving the idle channel, the idle bit in the general status register remains set. Go Ahead: The occurrence of this sequence can be used to generate an interrupt as described earlier. The receive circuitry will not recognize a frame abort followed by a flag as go ahead. C-Channel Reception: The information contained in channel-1 of the incoming ST-BUS (CDSTi) is shifted into the CChannel Status Register during the Internal Timing Mode. Transparent Data Transfer: By setting the IFTF bits in the Control Register to select the transparent data transfer, the receive section can be made to disable the protocol functions like Flag/Abort/GA/Idle detection, zero deletion, CRC calculation and address comparison. The received data is shifted in from CDSTi and written to receive FIFO in bytewide format. If the Protocol Controller is in the Internal Timing Mode and the Timing Control bits are set to 2, 6 or 7 bits/ frame, the respective MSBs of each byte are only to be read from the data bus. The transparent data transfer facility is not available when the Timing Control bits are set to one bit/frame. The receive section can be disabled in software immediately using the RxEN bit in the Control Register. The operation of the receiver is similar in the External Timing Mode. Receive Overflow: Receive overflow occurs when the receive section attempts to load a byte to an already full receive FIFO. This status can be used to generate the interrupt as described earlier.
3-73
MT8952B
ISO-CMOS
The block schematic of one such application is shown in Figures 15 and 16. They refer to the primary and secondary ends of a voice/data communication link using the Digital Network Interface Circuits (DNIC). Each end is associated with one DNIC which interfaces twisted wire pair to the digital data rate up to 160kbps (2B+D, framing signal and housekeeping information).
Typical Connection
A typical connection to the HDLC Protocol Controller is shown in Figure 14. The parallel port interfaces with 6800/6809 type processors. The bits A0-A3 are the addresses of various registers in the Protocol Controller. The microprocessor can read and write to these registers treating them as memory locations. The serial port transmits/receives the packetized data. It can be connected to a digital transmission medium or to a digital network interface circuit. The TEOP and REOP are the `end of packet' signals on transmit and receive direction respectively. F0i and CKi are the timing signals with CKi accepting either the bit rate clock or 2 x bit rate clock in the internal timing mode. TxCEN and RxCEN are the enable inputs in the External Timing Mode. WD is the output of the watchdog timer. It goes LOW when the timer times out or if the RST input is held LOW. This output can be used to reset the associated microprocessor. The RST is an active LOW input which resets the entire circuitry.
Primary End of the Link:
The MT8952B is operating in the internal timing mode with the C-channel transceiver action enabled. The processor loads the data or control information (D Channel) in the transmit FIFO which is packetized in HDLC format and shifted out serially during the selected channels of the outgoing ST-BUS (CDSTo). The channels and the number of bits per frame (frame period=125sec) can be selected by TC0-TC3 bits in the Timing Control Register. Since channel 1 is reserved for the C-channel information and channels 2 and 3 carry B-channels (64 kbps each), the D-channel information can only be sent on channel-0. Similarly the incoming packets on CDSTi are loaded into receive FIFO after the removal of all overhead bits and checked for any errors. The microprocessor will then read the data from the receive FIFO. The DNIC (MT8972) is selected to operate in single port, master mode with the digital network (DN) option enabled. The B-channels, B1 and B2, are shown connected directly to the DNIC. Hence, these should be in ST-BUS format enabled at the appropriate timeslot (channels 2 and 3). It can be
Applications
The MT8952B has a number of applications for transferring data or control information over a digital channel while providing built-in error detection capability. In combination with the MT8972 (the Digital Network Interface Circuit), it can be used to transmit digital data over a twisted wire pair.
TIMING AND CONTROL F0i CKi RST
D0-D7 PARALLEL INTERFACING WITH 6809 TYPE PROCESSORS R/W CS HDLC Protocol E A0-A3 Controller
CDSTo TEOP SERIAL PORT WITH FORMATTED CDSTi REOP DATA
MT8952B
TxCEN
WD RxCEN IRQ
VDD
VSS
Figure 14 - Typical Connection Diagram
3-74
ISO-CMOS
MT8952B
D0-D7 R/W M I C R O P R O C E S S O R CS E A0-A3 WD RST IRQ HDLC PROTOCOL CONTROLLER C4 F0 MT8952B CDSTi DSTo CDSTo DSTi MT8972 DIGITAL NETWORK INTERFACE CIRCUIT TO TWISTED WIRE PAIR (160 kbits/sec)
F0i
CKi MS0 0 MS1 0 MS2 0
B-CHANNELS (2 X 64 kbits/sec Max)
Primary Terminal End
Network Interface
Network
Figure 15 - HDLC Protocol Controller at the Primary End of the Link
D0-D7 R/W M I C R O P R O C E S S O R CS E A0-A3 WD RST IRQ MT8952B CDSTi HDLC PROTOCOL CONTROLLER C4 F0 DSTo CDSTo DSTi
MT8972 DIGITAL NETWORK INTERFACE CIRCUIT TO TWISTED WIRE PAIR (160 kbits/sec)
F0i
CKi MS0 0 MS1 0 MS2 1
B-CHANNELS (2 X 64 kbits/sec Max)
Secondary Terminal End
Network Interface
Network
Figure 16 - HDLC Protocol Controller at the Secondary End of the Link the outputs of voice codecs (MT896X) providing voice communication or data codecs (MT8950) for communication between RS232-C type terminals. It is possible to use the HDLC protocol on B1 and B2 channels to provide the error detection. This can be done by using a separate MT8952B enabled appropriately to shift out the formatted data during channels 2 and 3 or by multiplexing the same MT8952B between B- and D- channels.
3-75
MT8952B
ISO-CMOS
The timing signals like CKi (C2i or C4i) and F0i are provided externally at the primary end and at the secondary end, they are derived from the received data. Although this application describes the communication between two stations over a dedicated link, it can be modified to serve a switched communication path by additional control functions and a call set-up procedure many of which can be achieved in software.
Secondary End of the Link:
At the secondary end of the communication link, a similar procedure is adopted to transmit/receive the data and control information. The MT8952B operates in the Internal Timing Mode as at the primary end, but the DNIC (MT8972) is selected to operate in single port, slave mode with the digital network capability enabled. The other functions and procedures are similar to those at the primary end.
3-76
ISO-CMOS
Absolute Maximum Ratings*
Parameter 1 2 3 4 5 6 Supply voltage Voltage on any pin (other than supply pins) Current on any pin (other than supply pins) DC Supply or ground current Storage temperature Package power dissipation Cerdip Plastic Symbol VDD VI II / IO IDD / ISS TST PD PD -65 Min -0.3 VSS-0.3
MT8952B
Max 7.0 VDD+0.3 25 50 150 1.0 0.6
Units V V mA mA C W W
* Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics 1 2 3 4 Supply Voltage Input HIGH voltage Input LOW voltage Frequency of operation Sym VDD VIH VIL fCL Min 4.75 2.4 VSS Typ 5.0 Max 5.25 VDD 0.4 5.0 Units V V V MHz For a Noise Margin of 400 mV For a Noise Margin of 400 mV When clock input is at twice the bit rate. Test Conditions
5 Operating temperature TA -40 25 85 C Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing.
DC Electrical Characteristics - Voltages are with respect to ground (VSS) unless otherwise stated.
VDD=5V5%, VSS=0V, TA=-40 to 85C.
Characteristics 1 2 3 4 5 6 7 8 9 10 11 12 O U T P U T I N P U T Supply Current (Quiescent) Supply current (Operational) Input HIGH voltage Input LOW voltage Input leakage current Input capacitance HIGH switching point for Schmitt Trigger (RST) input LOW switching point for Schmitt Trigger (RST) input Hysteresis on Schmitt Trigger (RST) input Output HIGH current (on all the outputs except IRQ) Output LOW current (on all the outputs including IRQ) Output capacitance
Sym IDD IDD VIH VIL IIZ Cin VT+ VTVH IOH IOL Co
Min
Typ 1 0.4
Max 10 1.0 0.8 10
Units A mA V V A pF V V V mA mA pF
Test Conditions Outputs unloaded and clock input (CKi) grounded *See below
2.0
10 4.0 1.0 0.5 -5 5 -16 10 15
VOH=2.4 V VOL=0.4 V
Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. * Outputs unloaded. Input pins 12 and 25 clocked at 2048 kHz. All other inputs at VSS. 3-77
MT8952B
ISO-CMOS
AC Electrical Characteristics - Microprocessor Interface - (Figures 17 and 18)
Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics 1 2 3 4 5 6 7 8 9 10 11 12 Delay between CS and E clock Cycle time E Clock pulse width HIGH E Clock pulse width LOW Read/Write setup time Read/Write hold time Address setup time Address hold time Data setup time (write) Data hold time (write) E clock to valid data delay Data hold time (read)
Sym tCSE tCYC tEWH tEWL tRWS tRWH tAS tAH tDSW tDHW tDZL tDZH tDLZ tDHZ
Min 0 205 145 60 20 10 20 60 35 10
Typ
Max
Units ns ns ns ns ns ns ns ns ns ns
Test Conditions
145 10 60
ns ns
Test load circuit 1 (Fig. 26) CL=200pF Test load circuit 3 (Fig. 26)
Timing is over recommended temperature & power supply voltages (VDD=5V5%, VSS=0V, TA=-40 to 85C). Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing.
CS tCSE E tr tf tCYC tEWH
E clock initiates and terminates the write cycle
tEWL
CS tCSE E
CS initiates and terminates the write cycle
tRWS R/W tAS A0-A3 tDSW D0-D7 tAH
tRWH
tDHW
NOTE: The write cycle can be initiated either by the falling edge of CS or the rising edge of E clock whichever occurs last. Similarly the cycle can be terminated by CS (rising edge) or E clock (falling edge) whichever occurs first. The timing relations are to be referenced from the active edge initiating or terminating the cycle
Figure 17 - Timing Information for MPU Write
3-78
ISO-CMOS
MT8952B
CS tCSE E tr tf tCYC tEWH
E clock initiates and terminates the read cycle
tEWL
CS tCSE E CS initiates and terminates the read cycle
tRWS
tRWH
R/W tAS A0-A3 tAH
tDZL tDZH D0-D7 High Impedance VALID DATA
tDLZ tDHZ High Impedance
NOTE: The read cycle cn be initiated either by the falling edge of CS or the rising edge of E clock whichever occurs last. Similarly the cycle can be terminated by CS (rising edge) or E clock (falling edge) whichever occurs first. The timing relations are to be referenced from the active edge initiating or terminating the cycle.
Figure 18 - Timing Information for MPU Read
E
tIRQR IRQ
Figure 19 - Interrupt Request Release Time
F0i
tWDHL WD
tWDLH
Figure 20 - Watchdog Timer Input and Output
3-79
MT8952B
ISO-CMOS
AC Electrical Characteristics - Serial Port, RESET, WD Timer and IRQ Release Time
(Figures 19, 20, 21 and 22).
Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics 1 2 3 4 5 6 7 8 9 Interrupt request release time WD output delay HIGH to LOW WD output delay LOW to HIGH TEOP/REOP output delay TEOP/REOP output hold time CDSTo delay from CKi CDSTi setup time CDSTi hold time RESET pulse width
Sym tIRQR tWDHL tWDLH tEOPD tEOPH tSTOD tSTiS tSTiH tRST
Min
Typ
Max 120 135 135 110 110 125
Units ns ns ns ns ns ns ns ns
Test Conditions Test load circuit 2 (Fig.26) Test load circuit 1 (Fig.26) Test load circuit 1 (Fig.26) Test load circuit 1 (Fig.26) Test load circuit 1 (Fig.26) Test load circuit 1 (Fig.26)
20 65 100
ns
Timing is over recommended temperature & power supply voltages (VDD=5V5%, VSS=0V, TA=-40 to 85C). Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing.
tRST RST
Figure 21 - RESET Timing
End Flag or Abort Sequence Flag or Idle Sequence
CKi tSTOD CDSTo tEOPD TEOP tSTiS tSTiH tEOPH
CDSTi tEOPD REOP tEOPH
Figure 22 - Serial Port Input and REOP, Output and TEOP
Note: The frequency of the clock input CKi is assumed to be at the output bit rate. However, it can be at twice the bit rate in the Internal Timing Mode. 3-80
ISO-CMOS
MT8952B
AC Electrical Characteristics - Serial Port in External Timing Mode - (Figure 23 )
Voltages are with respect to ground (VSS) unless otherwise stated.
Characteristics 1 2 3 4 5 6 7 8 Clock period on CKi pin CKi transition time TxCEN/RxCEN setup time TxCEN/RxCEN hold time CDSTi setup time CDSTi hold time CDSTo delay CDSTo disable time
Sym tCEX tT tCENS tCENH tSTiS tSTiH tSToZL tSToZH tSToLZ tSToHZ
Min 400
Typ
Max
Units ns
Test Conditions
20 60 40 20 65 125 85
ns ns ns ns ns ns ns Test load circuit 1 (Fig. 26) CL=150pF Test load circuit 3 (Fig. 26)
Timing is over recommended temperature & power supply voltages (VDD=5V5%, VSS=0V, TA=-40 to 85C). Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing.
tCEX CKi tT
TxCEN/ RxCEN
tCENH tCENS tSTiS tSTiH
CDSTi tSToZL tSToZH CDSTo
HIGH IMPEDANCE
VALID DATA tSToHZ tSToLZ
HIGH IMPEDANCE
Figure 23 - Serial Port Inputs and Outputs in External Timing Mode
Note: The frequency of the clock input (CKi) should be at the output bit rate in the External Timing Mode.
F0i 125 sec ST-BUS Channel 31 Channel 0 Channel 1 Channel 2
********
Channel 29
Channel 30
Channel 31
Channel 0
Least Significant Bit (D0 on the Data Bus)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
3.9 sec
Most Significant Bit (D7 on the Data Bus)
Figure 24 - ST-BUS Format
3-81
MT8952B
ISO-CMOS
AC Electrical Characteristics - Serial Port in Internal Timing Mode - (Figure 25)
Voltages are with respect to ground (VSS) unless otherwise stated .
Characteristics 1 2 3 4 5 6 7 8 Frame Pulse (F0i) width Frame Pulse (F0i) setup time Frame Pulse (F0i) hold time CDSTo delay from clock input CDSTi setup time CDSTi hold time C2i clock period C4i clock period
Sym tF0iW tF0iS tF0iH tSToZL tSToZH tSTiS tSTiH
tC2i tC4i
Min 50 30 20
Typ
Max
Units ns ns ns
Test Conditions
See note 3. See note 3. Test load circuit 1 (Fig. 26)
125 20 65 400 200
ns ns ns ns ns
Timing is over recommended temperature & power supply voltages (VDD=5V5%, VSS=0V, TA=-40 to 85C). Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. tF0iW F0i tF0iH CKi (C4i) tC2i CKi (C2i) tF0iS tC4i
tSToZL tSToZH CDSTo
HIGH IMPEDANCE
Ch. 0 Bit 7 tSTiS tSTiH
Ch. 0 Bit 6
Ch. 0 Bit 5
CDSTi
Ch. 31 Bit 0
Ch. 0 Bit 7
Ch. 0 Bit 6
Ch. 0 Bit 5
Figure 25 - Serial Port Input and Output in ST-BUS Format (Internal Timing Mode)
Note: 1. Channels 0 to 4 can only be active on CDSTi and CDSTo in the Internal Timing Mode. 2. Clock input CKi can be either of the ST-BUS clocks C2i (2.048MHz) or C4i (4.096 MHz) in the Internal Timing Mode. 3. The Frame Pulse set up and hold time measurements are to be referenced from the falling edge of C4i or the rising edge of C2i depending on the clock selected.
VDD From output under test CL Test point CL= 200 pF for measurements on Data Bus 150 pF for measurements on CDSTo 50 pF for others RL=1k From output under test CL Test point From output under test CL Test point RL=1k S1 A
VDD
B VSS
Test load circuit- 1
Test load circuit- 2
Test load circuit - 3
Note: S1 is in position A when measuring tPLZ and in position B when measuring tPHZ. See note below.
Figure 26 - Test Load Circuits
Note: Active Low to High impedance times are measured from the disabling signal edge to the time when Vout has increased by 0.5 volts. Active High to High impedance times are measured from the disabling signal edge to the time when Vout has decreased by 0.5 volts.
3-82

▲Up To Search▲

Price & Availability of MT8952

	To Download MT8952 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .